![]() ![]() This was not an easy task so if you don’t have some decent wood working tools available, like a band saw, you might not want to use a solid piece of wood.Īs an alternative, you could use 1/4 inch thick plywood to create three layers. I’m sure there's more than one way to handle this but as you can see from my pictures, I wanted to keep the acrylic in one piece for stability, so I chose to work the wood core in a way that would fill the void in the acrylic but overlap the acrylic at the point where it attaches to the staff. This takes a bit of careful planning and design. This is actually my second blade design because the first did not look right after I saw it on the staff. Once I cut the template, I mounted it on my old staff to make sure the size and look was what I wanted. ![]() Drill a couple holes in the acrylic and then use the jigsaw to remove the remaining material. Go to your local hardware store and buy a special drill bit for acrylic. One note, if you have never drilled through acrylic - do not do it with a regular drill bit. Next, transfer that inner opening to the acrylic and remove that piece. This is also thick enough to keep the acrylic strong enough not to break later. Going back to my template, I sketched out the area inside the blade, keeping at least 2 inches of thickness around the edges. You might crack it.Īfter doing some sample testing with the leds to see how I wanted the lights to shine through the acrylic, I decided that I would set them back about 2 inches from the edge of the blade. Be careful to not apply too much pressure to the acrylic while cutting. I found that my jigsaw worked perfectly to cut these shapes. Using the template you created, transfer that to the acrylic and the foam board. A decent piece of cardboard or heavy stock paper would also work just fine. I had 1/2 inch poster board lying around that was large enough for this purpose. Transfer that to a template that will be used to cut the other materials. Using the 2x4 acrylic sheet as your size limit for this project, cover it with some paper and start sketching a design that appeals to your needs. I may revisit this again later to come up with a thinner design but that might come at a risk of a more fragile acrylic blade which I want to avoid. Initially, I also wanted to put glowing designs or alchemy symbols on the side of the blade as well but after a bit of trial and error, it would have made the blade over 2 inches thick and would have looked less authentic. My goal was to keep the overall width under 1 inch. It needs to look like a thin metal blade so design is critical. This is going to be a scythe blade so I did not want it too thick. Led light strip - Approximately 6-8 feet of length Ĭonsider your materials and design carefully up front.I salvaged this from some old signs that my company was throwing away but the foam board mentioned above will work just as well. I used 1/2 poster board with black foam inside. You can use the 2 inch thick foam boards but it will require a little more work to reduce the overall thickness of your blade. OPTIX 0.22-in x 24-in x 48-in Clear Acrylic Sheet - should be able to find this at your local hardware store.Here's what you'll need for this instructable Inspired by a glowing red "EXIT" sign near my office cube, I decided that I could rebuild the scythe blade with glowing red edges to make this a very dramatic scythe at night. The current model was well received wherever I went but it was time for an upgrade. This year, my focus was on my Reaper Scythe (. Your weapon takes 45% less durability damage while affected by War Cry.Every year I look at my projects that are still useful and try to find ways to improve them. Melee critical hits do increased impact and add 1.5 seconds of stun when the enemy is interrupted. Ninja deals 28% more melee weapon damage to enemies that are stunned, staggered, or knocked back. Steals 5 energy every 4 melee strikes against an enemy. Melee kills increases movement speed by 30% for 3 seconds. Shadow Stance increases edged weapon damage during Shadow Stance by an additional 70%.Īssassination stacks now grants a 3% bonus, per stack, to critical hits with edged melee weapons. Scythes deal 48% increased damage to slowed or snared targets. Increases damage of swords, axes, and scythes by 24%.Įvery 4th hit with a melee weapon restores 24 base health. See the Hero Loadout blog for details.Ĭritical hits from melee weapons deal 15% of hit damage every second for 3 seconds while reducing movement speed by 30%.Ĭritical hits from the Ninja's edged weapons deal 30% of hit damage over time while reducing movement speed of target by 30%. Some content on this page may contain information about subclasses, perks, or heroes that no longer exist or have been significantly altered. This page may contain information affected by the Hero Loadout update.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |